Know more about your bore

It is important to know your bore, where you are pulling water from and if you are at risk of your bore being unserviceable.

Expand all | Close all

My bore

To understand your bore and how you can better manage your water use, you should first find your bore using the 'Know your bore' tool .

With this tool you can find out:

  • find out which water resource your bore is pulling from
  • review your bore report/statement the department has on file and
  • see if your bore may be at risk of running out of water.

To help you understand your 'Statement of Bore', read information on how to read this statement PDF (359.5 KB).

My bore information is incorrect

If your bore information is incorrect, send us an email providing us with following updated information:

  • bore number
  • owner name
  • contact phone
  • contact email
  • details needing updating

If you have any questions or need help feel free to contact the Water Resources Division on 08 8999 4455.

About bores

Bores are a narrow hole drilled down into an aquifer to extract groundwater.

Bores, like any plumbing device are subject to degradation and even failure.

This can be due to age or improper design.

Domestic bores are typically lined with 150mm steel or PVC pipe to prevent the hole from collapsing.

The pipe is perforated with slots opposite the aquifer to allow water to enter.

Special borehole pumps are placed in the bore with their inlet located at some distance above the slots.

When the pump is turned on it causes a localised cone shape draw down of the water table around the bore.

The cone gradually expands away from the bore until a balance is reached between the amount of water pumped and the rate of inflow from areas of the aquifer surrounding the cone.

A domestic bore would typically influence the surrounding area by a few tens of metres.

When the pump is turned off the water table gradually returns to close to its original level.

Information about most bores is registered with Water Resources Division. This information includes:

  • registered bore number (all bores in the NT have a unique registered bore number)
  • depth and type of construction
  • location of screens/slots
  • water quality at the time of construction.

What issues can I have with my bore

Being aware of the signs of bore failure will allow you to plan for a new or extended bore or to plan for a temporary contingent water supply.

The following are signs of bore failure.

  • pump spurts (water and air)
  • no water
  • change in water quality
  • discoloured water or sediment/sand in water
  • reduced pressure/pumping rate (less sprinklers running than previous)
  • pump switches off (overheat sensor).

Possible causes of bore failures

Types of bore failures can be many and varied. It is important for you to know, monitor and continually maintain your bore.

  1. Improper design such as:
    1. design of bore screen
    2. design of gravel pack.
  2. Faulty construction such as:
    1. wrong placement of bore screen
    2. improper jointing of pipe and bore screen
    3. inadequate development.
  3. Faulty operation such as:
    1. over pumping
    2. poor maintenance.
  4. Mechanical failure such as:
    1. shearing and collapse due to excess load
    2. lodging of foreign objects, including pump components.
  5. Corrosion.
  6. Incrustation.
  7. Interference between bores.
  8. Adverse aquifer conditions like:
    1. lowering of water table
    2. deterioration of water quality.

Low water levels are not the only reason for bore failure or inefficiency.

Low water levels contribute to and result in the any of the following.

Possible bore issueDescription
Improper design The use of inappropriate materials or improperly placed screens/slots can cause bore failure.
Borehole instability Damaged casing and screens, borehole wall collapse due to, corrosion or excessive water flow in the bore.
Biofouling Installing and pumping a bore in some aquifers can increase the amount of oxygen and nutrients in the water.
Bacteria such as iron-fixing bacteria, can thrive under these conditions.
This is quite common in bores throughout the Darwin rural area.
For more information refer to the Iron fouling of Groundwater factsheet PDF (588.2 KB).
Corrosion Some aquifers are slightly acidic and can eventually corrode metal bore casings.
Over pumping This is the most common issue that leads to premature bore problems.
It not only depletes the groundwater, but it rapidly increases the rate of corrosion, incrustation and biofouling related issues.
It can also increase the amount of sediment particles moving toward the bore causing plugging of the screens or perforated casing where water flows into the bore.

How do I maintain my bore?

Many problems with bores can be fixed either by the way they are operated or with maintenance.

In some cases the option may be to drill a new bore, reconstruct or deepen the existing one.

The first actions to be considered include:

  • reduce your water usage
  • reduce your pumping rate if possible
  • lower the pump if possible
  • have the bore cleaned to remove sand and silt as well as encrustation in the slots.

Refer to our fact sheet for more information on looking after your bore PDF (236.7 KB).

Contacts

Contact Water Resources Division on 08 8999 4455 or send an email to waterresources@nt.gov.au

Last updated: 02 October 2019

Share:

Was this page useful?

Describe your experience

More feedback options

To provide comments or suggestions about the NT.GOV.AU website, complete our feedback form.

For all other feedback or enquiries, you must contact the relevant government agency.